利用華為模擬器eNSP來設計邏輯網絡拓樸圖，有一臺路由器AR201，一臺二層交換機S5700，二臺PC主機。其之間用線纜連接并作好標注。
注意：連接好線纜后設置PC1和PC2的IP地址、子網掩碼及網關，其中網關為路由器中設置的IP地址。
1 實現不同vlan間的通信方法之——單臂路由
1.1 配置交換機
system-view
sysname SW1 //設置交換機名字為SW1
vlan batch 2 3 //連續創建vlan 2 3
interface Ethernet 0/0/2
port link-type access //設置端口類型為access
port default vlan 2 //將接口劃分到vlan 2
quit
interface Ethernet 0/0/3
port link-type access
port default vlan 3
quit
interface Ethernet 0/0/1
port link-type trunk //設置端口類型為trunk
port trunk allow-pass vlan 2 3 //華為交換機默認不支持其他vlan通過，除去vlan 1,允許trunk端口通過vlan 2 3
1.2 配置路由器
system-view
sysname R1 //設置路由器名字R1
display interface brief //顯示接口概要
interface GigabitEthernet 0/0/0.1
dot1q termination vid 2 //封裝dot1q協議,該子接口對應vlan 2
ip address 192.168.2.254 24 //設置子接口IP地址和子網掩碼
arp broadcast enable //開啟子接口的ARP廣播
quit
interface GigabitEthernet 0/0/0.2
dot1q termination vid 3
ip address 192.168.3.254 24
arp broadcast enable
quit
display ip interface brief //顯示接口IP的簡要狀態信息
ping 192.168.2.2 //測試能夠ping通
ping 192.168.3.3
2 配置三層交換
[SW2]vlan batch 2 3
[SW2]interface GigabitEthernet 0/0/1
[SW2-GigabitEthernet0/0/1]port link-type access
[SW2-GigabitEthernet0/0/1]port default vlan 2
[SW2-GigabitEthernet0/0/1]interface GigabitEthernet 0/0/2
[SW2-GigabitEthernet0/0/2]port link-type access
[SW2-GigabitEthernet0/0/2]port default vlan 3
<SW2>display vlan
The total number of vlans is : 3
--------------------------------------------------------------------------------
U: Up; D: Down; TG: Tagged; UT: Untagged;
MP: Vlan-mapping; ST: Vlan-stacking;
#: ProtocolTransparent-vlan; *: Management-vlan;
--------------------------------------------------------------------------------
VID Type Ports
--------------------------------------------------------------------------------
1 common UT:GE0/0/3(D) GE0/0/4(D) GE0/0/5(D) GE0/0/6(D)
GE0/0/7(D) GE0/0/8(D) GE0/0/9(D) GE0/0/10(D)
GE0/0/11(D) GE0/0/12(D) GE0/0/13(D) GE0/0/14(D)
GE0/0/15(D) GE0/0/16(D) GE0/0/17(D) GE0/0/18(D)
GE0/0/19(D) GE0/0/20(D) GE0/0/21(D) GE0/0/22(D)
GE0/0/23(D) GE0/0/24(D)
2 common UT:GE0/0/1(U)
3 common UT:GE0/0/2(U)
VID Status Property MAC-LRN Statistics Description
--------------------------------------------------------------------------------
1 enable default enable disable VLAN 0001
2 enable default enable disable VLAN 0002
3 enable default enable disable VLAN 0003
<SW2>
<SW2>
<SW2>display interface brief
PHY: Physical
*down: administratively down
(l): loopback
(s): spoofing
(b): BFD down
(e): ETHOAM down
(dl): DLDP down
(d): Dampening Suppressed
InUti/OutUti: input utility/output utility
Interface PHY Protocol InUti OutUti inErrors outErrors
GigabitEthernet0/0/1 up up 0% 0% 0 0
GigabitEthernet0/0/2 up up 0% 0% 0 0
GigabitEthernet0/0/3 down down 0% 0% 0 0
GigabitEthernet0/0/4 down down 0% 0% 0 0
GigabitEthernet0/0/5 down down 0% 0% 0 0
GigabitEthernet0/0/6 down down 0% 0% 0 0
GigabitEthernet0/0/7 down down 0% 0% 0 0
GigabitEthernet0/0/8 down down 0% 0% 0 0
GigabitEthernet0/0/9 down down 0% 0% 0 0
GigabitEthernet0/0/10 down down 0% 0% 0 0
GigabitEthernet0/0/11 down down 0% 0% 0 0
GigabitEthernet0/0/12 down down 0% 0% 0 0
GigabitEthernet0/0/13 down down 0% 0% 0 0
GigabitEthernet0/0/14 down down 0% 0% 0 0
GigabitEthernet0/0/15 down down 0% 0% 0 0
GigabitEthernet0/0/16 down down 0% 0% 0 0
GigabitEthernet0/0/17 down down 0% 0% 0 0
GigabitEthernet0/0/18 down down 0% 0% 0 0
GigabitEthernet0/0/19 down down 0% 0% 0 0
GigabitEthernet0/0/20 down down 0% 0% 0 0
GigabitEthernet0/0/21 down down 0% 0% 0 0
GigabitEthernet0/0/22 down down 0% 0% 0 0
GigabitEthernet0/0/23 down down 0% 0% 0 0
GigabitEthernet0/0/24 down down 0% 0% 0 0
MEth0/0/1 down down 0% 0% 0 0
NULL0 up up(s) 0% 0% 0 0
Vlanif1 down down -- -- 0 0
<SW2>
<SW2>
<SW2>system-view
Enter system view, return user view with Ctrl+Z.
[SW2]
[SW2]
[SW2]
[SW2]interface vlanif 2
[SW2-Vlanif2]ip address 192.168.2.254 24
[SW2-Vlanif2]
Aug 8 2018 17:27:39-08:00 SW2 %%01IFNET/4/LINK_STATE(l)[55]:The line protocol I
P on the interface Vlanif2 has entered the UP state.
[SW2-Vlanif2]interface vlanif 3
[SW2-Vlanif3]ip address 192.168.3.254 24
[SW2-Vlanif3]quit
[SW2]ping 192.168.2.1
[SW2]ping 192.168.3.1
<SW2>save //切換到用戶模式下（ctrl+z）保存配置信息
